Raven MTX Betriebsanweisung

MTX A PRODUCT OF: A PRODUCT OF: USER GUIDE VOL. 1

10 1. Using a microfiber cloth, clean the RAVEN MTX screen to remove dust and fingerprints. 2. Spray the revitalizer solution directly onto

11 3. Using a microfiber cloth LIGHTLY spread the solution around to cover the entire screen. a. IMPORTANT: DO NOT WIPE/BUFF AWAY ALL OF THE REV

12 memory is recommended - Any Mac Pro produced after 2010 is ideal and will meet all the requirements, though MacBook Pros and iMacs meeting the r

13 Setting RAVEN MTX On Its Legs When your RAVEN MTX arrives, you will first need to put it onto its legs. IMPORTANT – The RAVEN MTX is heavy

14 3. With two people on each side to steady the RAVEN MTX, have one individual underneath insert the screws upward through the treaded holes.

15 4. Using a 7/16” crescent wrench and a ratchet with 10mm socket, insert the bolts through the holes that join the legs to the chassis and tig

16 Attaching Wired Keyboard and Trackball or Mouse For seamless integration and ideal ergonomics, we recommend the following accessories: Kens

17 003471/dp/B005L38VPC http://www.logitech.com/en-us/product/wireless-solar-keyboard-k750-mac 1. Using a Phillips screwdriver, remove the keyboa

18 3. Feed USB cable for trackball through the left slot of the trackball tray and place in the trackball. (Note: Left handed users can place

19 4. Place trackball back into the chassis. 5. Feed the USB for the keyboard through the hole in the center of the

2 Updated 10/24/13 Table of Contents Important Safety Notes Before You Start ...

20 keyboard deck. 6. Plug in both trackball and keyboard into the top slots of the internal USB board. 7. Place key deck back into the cha

21 8. Replace all screws to secure trackball tray and keyboard deck. Powering On Your RAVEN MTX There are two power connections for the RAV

22 2. Power inlet on the RAVEN MTX analog electronics Box. Powers control modules, meter bridge, and analog monitoring electronics. Both power c

23 2. Remove the pan and set aside.

24 3. Make all cable connections 4. Replace pan by setting in the front part first. The front edge of the pan sits on top of the front cross bra

25 Audio Interface Cabling and Initial Setup If you mount your computer audio interface in the integrated 19” rack under the RAVEN MTX you will n

26 2 Connect the other end of the cable to the outputs of your chosen interface/converter. 3 Connect a DB25 cable to the Speaker Output of the RA

27 1. Remove 12 meter access panel screws 2. Remove meter access panel 3. Locate blue calibration block on meter cards, you will find one behind

28 3 Turn computer on and computer will sync to display. 4 In System Preferences, click Displays and select the RAVEN MTX as your main display.

29 Correct Touch Angle Incorrect Touch Angle ● Do not use a stylus or other object to calibrate the screen. ● After calibratio

3 Restoring to Factory Default ... 56 Edit window ...

30 4 Open Setup > Peripherals > Then go to the Midi Controllers tab. Under the dropdown menu, select HUI control, Receive from vcontrol

31 These settings will save in Pro Tools for future sessions. Launching RAVEN MTX Software The following sequence must be followed in order to

32 ● Calibration must be done using a direct and natural touch angle. Do not calibrate with a bend in your wrist or from an extreme angle. Failure

33 2) Navigate To The Pro Tools Heading > Preferences 3) Then, click the “Mixing” tab 4) Check the box next to: “Always Fill Channel Strips wh

34 top to bottom. Note: Confirm the tracks correctly aligned before moving on as incorrect alignment will affect your use of RAVEN negatively. 12)

35 The RAVEN Toolbars provide controls typical of most DAW’s. From the RAVEN Mixer you are able to have MultiTouch access to all of the controls

36 Fine Faders - Tap the DB display window to put single channels into fine mode. Automation Modes Automation on the RAVEN MIXER: 1. Press

37 Automation on the FLOATING MIXER: 1. Pressing the button above the INS button, the automation drop-down menu will appear. 2. Select the

38 1. Press the Icon slot below the fader module. A floating icon window will appear 2. Tap an icon and a yellow box will appear around selected

39 4. To remove an icon, touch the blank icon box in the palette, and then touch the channel icon slot you wish to remove. RAVEN Toolbar

4 Important Safety Notes Before You Start This symbol indicates that dangerous voltage constituting a risk of electric shock is present within

40 The RAVEN Toolbar rests on the bottom of the screen and is the control center for many essential features. It can be viewed with a single, doubl

41 Note: This can be very helpful when using an internet browser or something that appears hidden behind RAVEN’s software overlay. 1. Power – E

42 4. Open/Close Last Plugin - Use this button to close plugin windows or to show the last open plugin. 5. Pan Left/Pan Right – This

43 Floating Navpad Window: Toolbar NavPad: Note: Press the Track Zoom button to toggle between individual Track Zoom or Track Zoom All.

44 Note: You can remove the Raven Mixer by touching the RAVEN Mixer button and see the actual Pro Tools mixer. Please note, the Pro Tools

45 We have also included the ability to control the response of the Fine Faders by double-tapping the Fine Faders button on the RAVEN Toolbar. Adj

46 12. Customize Toolbar – Tap this button to enter “Customize Toolbar” mode. Simply: a. Press the button and it will latch. b. Drag icons and

47 To customize your Floating Toolbar: • Press the Customize Toolbar button on the top left corner of the palette. • Drag desired tools to the

48 14. Save Layout – Saves your RAVEN toolbar layout, your Floating Toolbar layout and your configured Hotkeys to a specific button you can get

49 20. Memory Locations – These buttons function exactly the same as the memory locations feature in Pro Tools. Note: The smaller 6-panel are li

5 Moving Make sure the product is turned off, unplugged, and all cables have been removed. It will take a minimum of two people to move your RAVEN

50 Buttons will turn yellow when smart tool is activated. 15. Duplicate/Clip Loop - Easy tools to duplicate and loop sound clips in the

51 The floating mixer can be expanded or collapsed by pressing the “-“ or “+” button on the floating mixer header. The mixer can be viewed as 8,

52 Pressing the pan button will switch the top section of the mixer from automation modes to pan modes. Pressing the “X” button on the top ri

53 Users can also bank more quickly by using two-fingers on the faceplate of the fader tracks and swipe left or right to bank by eight tracks at a

54 Restore Factory Default/Factory Default – Restores the RAVEN software to factory settings. Stereo/Surround Meters - Switches th

55 2. Choose a folder you want to save the session to and give the folder a name. 3. Press Save. To Load a RAVEN Session: 1. Press the L

56 3. Your RAVEN session will now load exactly as you saved it. Restoring to Factory Default 1. Press the button for restore default 2.

57 RAVEN allows for single touch control over the Pro Tools edit window. Familiar tools and functions can be easily accessed with your fingertips,

58 On The Floating Mixer: 1 Hit the INS button on a given channel. The floating plugin window will then open. - The floating plugin wi

59 Plugins should only be touched when there is a large control that is easy to activate via touch. Otherwise, a mouse should be used to control th

6 Important Note About DVI Cables As in many studios, your computer may be located in a room far away from your console. For DVI cable lengths ove

60 RAVEN MTX Monitor Controller overview The RAVEN MTX is a full featured monitor controller that facilitates high fidelity, intuitive a

61 Left Control Module Headphone Section • Headphone Source Selection Encoder – Selects which audio source is being monitored on the headphones

62 o When LIGHTS button is ON, all inactive buttons will illuminate RED o When LIGHTS button is OFF, all inactive buttons will not illuminate •

63 o Auto Talk functionality requires an audio signal feed from your DAW that plays at a steady level when the DAW transport is playing, and stop

64 the Auto Talk track output level in your DAW and make sure it's a constant signal with little variation in amplitude. Surround Speaker Sele

65 has many applications. 1. Monitoring without headphones: Performers can monitor the audio without headphones and/or the engineer can Talkback t

66 Speaker Select Stereo Speaker Outputs RAVEN MTX sends attenuated audio to multiple pairs of speakers. In stereo mode, RAVEN MTX can send to t

67 To deactivate SPEAKER C subwoofer mode, press and hold Speakers A and C together. If SPEAKER C has also been paired with B, un-pair them by the

68 DB25. No patching will be required to instantly go back and forth between tracking and mixing, in Stereo or Surround (optional). MIX 1 Monitors

69 Inputs MAIN INPUTS DB25, channels 5,6 & 7,8 Outputs MASTER CUE A, B, C, D Console headphones CUE 2 STUDIO Pre Fade Source Through AUX

7 You may recover from SMT and its suppliers only direct damages up to the amount you paid for the product. You cannot recover for loss of present

70 MASTER STUDIO Pre Fade Source Through iDock Monitors two stereo sources: 30 pin iDock for iPod, iPhone 4 and prior, or 1/8th stereo input fo

71 When STUDIO button is active, talkback is injected into stereo STUDIO feeds. When CUE button is active, talkback signal is injected into all e

72 AC Inlet – Connect your power cable to this connector Aux Module – Connections for power and activation of Meter bridge, iDock, Aux Module, DA

73 5) XLRF - Aux In Left 6) XLRF - Aux In Right 7) XLRM - Slate Out (line level talkback out for "slating" takes) 8) XLRF - Auto Talk

74 Surround Module • Stereo SPKR A/ SURR L,R – Alternate ¼” stereo outputs. • Surround Speaker Output – DB25 connection for surround signals 1-

8 a damp cloth must be used, make sure to remove any excess water immediately after cleaning. To clean RAVEN MTX’s exterior metal parts use a si

9 Revitalizing the RAVEN MTX Glass The RAVEN MTX comes out of the box with a NanoGlide coating that repels oil, water, and leaves the surface incr